/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file    gpio.c
  * @brief   This file provides code for the configuration
  *          of all used GPIO pins.
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2025 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */

/* Includes ------------------------------------------------------------------*/
#include "gpio.h"

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/*----------------------------------------------------------------------------*/
/* Configure GPIO                                                             */
/*----------------------------------------------------------------------------*/
/* USER CODE BEGIN 1 */

/* USER CODE END 1 */

/** Configure pins as
        * Analog
        * Input
        * Output
        * EVENT_OUT
        * EXTI
     PA3   ------> OPAMP1_VINM0
     PA5   ------> OPAMP2_VINM0
     PA7   ------> OPAMP1_VINP
     PB0   ------> OPAMP2_VINP
     PB2   ------> OPAMP3_VINM0
     PB13   ------> OPAMP3_VINP
*/
void MX_GPIO_Init(void)
{

  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOC_CLK_ENABLE();
  __HAL_RCC_GPIOF_CLK_ENABLE();
  __HAL_RCC_GPIOG_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();
  __HAL_RCC_GPIOB_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(RUN_LED_GPIO_Port, RUN_LED_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin : MOTOR2_Z_Pin */
  GPIO_InitStruct.Pin = MOTOR2_Z_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  HAL_GPIO_Init(MOTOR2_Z_GPIO_Port, &GPIO_InitStruct);

  /*Configure GPIO pins : MOTOR2_I_U__Pin MOTOR2_I_V__Pin MOTOR2_I_U_A7_Pin */
  GPIO_InitStruct.Pin = MOTOR2_I_U__Pin|MOTOR2_I_V__Pin|MOTOR2_I_U_A7_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /*Configure GPIO pin : RUN_LED_Pin */
  GPIO_InitStruct.Pin = RUN_LED_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(RUN_LED_GPIO_Port, &GPIO_InitStruct);

  /*Configure GPIO pins : MOTOR2_I_V_B0_Pin MOTOR2_I_W__Pin MOTOR2_I_W_B13_Pin */
  GPIO_InitStruct.Pin = MOTOR2_I_V_B0_Pin|MOTOR2_I_W__Pin|MOTOR2_I_W_B13_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

}

/* USER CODE BEGIN 2 */

/* USER CODE END 2 */